Difference between revisions of "Mini Talon X-UAV from FPV Model"

Revision as of 00:54, 7 February 2016

January 2016

Contents 1 Introduction 1.1 Airframe and Controls 1.2 Specifications 1.3 Build/Layout 1.3.1 A Few Last Views 1.4 Maiden 2 See Also 2.1 Vendors to use for this project 2.2 Comments? Questions?
	Ready for fun!

Introduction

Decided to try the Mini Talon as a way to get a medium range plane I could easily throw in my car. I looked at the Twin Star and the Floater Jet but finally decided on the Mini Talon because my large Talon is such a great flyer and it is relativley inexpensive.

Airframe and Controls

I did decide to try a set of Digital servos mainly because I had them already. The linkage was changed to small Dubro 2-56 ball-ends on the Elevons because of the high miss-allignment btween the controll surface and the sevo arm travel.

Ball-end linkage on the elevons

For this build, I decided to try an RTFQ ReadyToFly 2.8 flight controller to save a few bucks and check out if they are reliable and as easy to set-up as my APM. I am using APMPlane 3.3 firmware.

For an OSD, I am running an RTFQ MicroMinium OSD with my own character set.

For radio gear I am using DragonLink V2 with the MicroRX Copter receiver.

Specifications

Build date - January 2016

Build/Layout

I won't spend anytime on pictures of assembling/gluing the foam bits together. I'll just show any mods and/or custom setups I did for this build. This starts with a simple layout with the Flight controller mounted on a plywood plate with rubber dampers attached between the wing support plates.

Flight Controller mounted on plywood plate with Micro MinimOSD servo taped to the top of the case

Layout showing the Flight Controller, Micro MinimOSD, FPV power module and GPS

On the front I built an "FPV" module which includes the VTx, DL 1.3G Dipole antenna, a Storm32 brushless gimbal control board, an Effio camera, a two or three axis gimbal with Mobius camera and a two way camera switch.

FPV module showing the DragonLink 1.3G Dipole antenna and a Low Pass filter which will not be used

FPV module - Bottom view with VTx aluminum shield and heatsink

To power the FPV module I printed a mount plate for a 12v regulator, a 5v regulator and an RMRC LC power filter. All three components are mounted on foam tape with wire ties to hold them down.

FPV Power Module

Power module schematic

A Few Last Views

Side view with VTx antenna

To install the VTx Dipole I had to design a simple 3D printed thumb wrench which would fit through the hole in the fuselage.

DragonLink dipole and wrench

Using a process I detail in "How To - Create a Kevlar Skid Shield", I added 1.7oz Kevlar to the landing skid areas and over the battery strap.

It's all about Kevlar!

Front view showing smaller 2 axis Gimbal and VTx cooling ports - Ready for Maiden!

Maiden

The maiden went very well! After all the anticipation, the initial launch was as uneventful as its bigger brother, my full size Talon. It literally just floated out of my hand without any drama or surprises what so ever. Unfortunately I had to keep it LOS as the MinimOSD decided to not work. I'll get it all sorted out along with some initial PID tuning hopefully on a day with sunshine and no wind :).

Here's a video of the maiden flight. Because I had to wait till after sundown for the wind to get reasonable, I was running out of light pretty quickly. Enjoy...

See Also

Mini-Talon on RC Groups

Vendors to use for this project

Ready To Fly Quads

R/C Dude Hobbies

Hobby King

Comments? Questions?

email me!