Strix StratoSurfer

© Mark Qvale - January, 2018

	New plane!

Introduction

Decided to try something different and having never gone down the Bixler road, this seemed like a good place to start. After reading much about this plane, I decided to start with a larger motor/prop combo. I also decided to try an Omnibus F3Pro flight controller to keep it light and simple.

General Specifications

Distributor - BangGood USA
Aircraft - X-UAV Mini Talon
Build Date - April 2017

Airframe Type -	Top Wing FPV Specialist		All-Up Weight -	TBAoz (TBAg) w/ 4S/7000 Li-ion Pack
Wingspan -	59 inches (1500mm)			TBAoz (TBAg) w/ 4S/5200 Li-Poly Pack
Length -	39 inches (1000mm)
Wing Area -	3.23 ft^2 (30dm^2)		*Wing Load w/5.2-4S -	TBA.0 oz/ft^2 (TBAg/dm^2)
Motor -	Sunnysky 2216-1250kv		Max Continuous Power (4S) -	370 watts continuous (4S)
Propeller -	8 x 7 Aeronaut Cam Carbon Folder		Max Prop Power -	325 watts @ 2550ft ASL
Static Thrust -	1150 @ 2550ft ASL		*Static Thrust/Weight -	0.TBA
Battery Type -	4S1P Li-ion/Li-po		Battery Capacity -	7000mah/3C or 5200mah/10C
In flight efficiency -	TBA		Flight Time -	TBA
COG -	65mm @ Wing root (Stock)		*With the	5200mAh pack

Flight Gear

The following are some of my selected components with links to some of my favorite vendors.

Power Set-up

For power on this build I have chosen the Sunnysky X2216-1250kv. For an ESC, I am using a HobbyKing Blue Series 40A with extra Low ESR capacitors added.

• Motor - Sunnysky 2216-1250kv
• ESC - Blue Series 40A
• Prop - Aeronaut Cam Carbon Folder 9x7]

For more informaion on setting up a pusher folding prop - How To - Set-Up a Pusher Style Folding Prop

• Battery - Multistar 4S/5200, 10C
  
  

Motor Mount

For the motor mount I designed and printed one that spaces the motor 6mm rearward and 19mm above the original mount to get the clearance needed for 7" & 8" props. Additionally, I printed a cowl to protect the motor and direct cooling air to the rear of the motor.

Motor mount parts

Mounted

ESC Mount

I decided to design and print a simple mount to hold the ESC. It mounts with four M3x6mm nylon screws and a wire tie to hold the ESC. This print is sized for a 25mm wide ESC.

ESC craddle

Flight Control

For flight control I have chosen the Omnibus F3Pro from Banggood. It is very inexpensive and in my experience completely reliable.

• Omnibus F3Pro

w/iNav 1.8.1

FC Mount

To mount the FC I drilled out the existing mount holes to 2.3mm then tapped them to M3 and flooded the tapped holes with thin CA. This makes them more than strong enough for a set of rubber M3x6mm stand-offs.

FC mount

RC Control

For radio gear I am using my standard DragonLink V2 system. I have mounted the DL dipole inside the verticle stabilizer. The RX is mounted on a printed deck below the GPS mount.

RX mount

GPS Mount

For the GPS I printed a mount plate to replace the white plate on the rear of the fuse. This is sized for a Ublox Mini M7 GPS.

• Mini Ublox M7/M8

Video Downlink

For the video downlink I am using an RMRC 1.2/1.3G VTx with a DragonLink video dipole. I will either run 400 or 800mw depending on where and how I am flying. For an FPV camera I have selected a Fatshark V2 700tvl unit because of its size and decent performance.

Airframe Build and Assembly

Stabilizers

On the tail linkage I used the stock linkage bits with metal gear digital servos.

Wings

Nothing new or special here. I added 1" (25mm) of 3 mil laminate to the leading edge. Linkage is the same as the elevators and servos are Corona DS929MG's.

Mods

Stay tuned

See Also

TBA

Project 3D Print Files

The following are the 3D print files shown in this build.

Image	Part Number	Part Description	Weight	Print File	Compatibility Notes
	52136	ESC Mount	6.7g	52136.STL	25mm wide ESC craddle
	52137	GPS Mount	3.3g	52137.STL	Mount for a Ublox Mini 7M GPS
	52138	Motor Cowl	4.0g	52138.STL	Motor and mount cover
	52139	RX Mount	4.2g	52139.STL	Mount platform for DL RX
	52140	19mm Offset Motor Mount	3.1g	52140.STL	Motor mount to allow 7 & 8 inch props

Some of the Vendors I used for this project

Banggood

Aloft Hobbies

Ready Made RC

Comments? Questions?

email me!