Difference between revisions of "RunCam Split Pan and Tilt and Cases"

Revision as of 16:17, 28 December 2017

July 2017

Contents 1 Introduction 2 Pan and Tilt 2.1 Parts & Hardware 3 RunCam Split Case 3.1 Parts and Hardware 4 See Also 4.1 Comments? Questions?
	The simple 180 degree Pan and Tilt

Introduction

This project started with the first RunCam Split (v1) which I bought to replace my Mobius with something more current and a little smaller. The first parts I did made up the v1 Pan and Tilt (shown above) which would bolt directly to my previous Pan and Tilts. After flying this for a bit, I decided I needed a case version I could easily move from plane to plane so I came up with several versions of the case.

I am only showing one version of the Pan and Tilt and one version of the simple case. For more parts including compatability information please see these two parts catalogs:

• Parts Catalog - Pan and Tilt Parts
• Parts Catalog - General Parts

Pan and Tilt

The Pan and tilt has an "open" frame to allow cooling air to circulate around and through the PCB. There are two sizes of servo plates available, one to accomodate my canopy mounts and a larger one to accomodate a common plywood or flat deck.

Parts & Hardware

Part Number  Part Description Print File  Compatibility  52100  Servo plate, flat, raised  52100.STL  Fits Turnigy RS5180MG servo or similar. Servo only, no gearing.  52092  Lower bracket, small  52092.STL  Supports all Camera Plates. See part sketch for mount hole spacing.  52062  Camera plate, RunCam Split  52062.STL  Fits all Yaw Brackets. Designed for the RunCam Split & Split v2 cameras. Use with 52067 and 52076 for v1 or 52135 for v2  52067  RunCam Split v1 PCB Cover, Top  52067.STL  Pair with 52062 camera plate for RunCam Split v1  52076  RunCam Split v1 SD Card Cover  52076.STL  Pair with 52062 camera plate for RunCam Split v1. Snaps into 52067 top cover  52135  RunCam Split v2 PCB Cover, Top  52135.STL  Pair with 52062 camera plate for RunCam Split v2 Hardware 4x M3 x 10mm Philips Head Screw, Nylon 4x M3 x 5mm Stand-off, Nylon 2x M3 x 12mm Philips Head Screw, Nylon 2x M3 Hex Nut, Nylon 4x M2 Hex nut 4x M2 x 10mm Socket Head Machine Screw 4x M2 Flatwasher 4x M2 Hex Nut 4x M2 x 6mm Flathead Screw 0.047" x 50mm Steel wire

Servo Selection:
Pan Servo - For this non-geared Pan and Tilt I selected the Turnigy™ TGY-180D 180 degree Digital Servo from HobbyKing. It is important to use a digital if you are also using a VTX of 600mw or more to avoid the noise these components can produce in the servo.

Tilt Servo - Many of the current 9-12 gram servos will fit the tilt plate. A Corona DS929MG is what I use.

RunCam Split Case

The case I am showing here is very simple. It is three parts for the v1 Split and two parts for the v2. It has an open frame so that air will circulate around the PCB. It uses the stock short camera module cable.

Parts and Hardware

Part Number  Part Description Print File  Compatibility  52076  RunCam Split SD Card Snap Cover  52076.STL  Fits 52067 Cover.  52067  RunCam Split v1 PCB Top Cover  52067.STL  Fits RunCam Split V1  52087  RunCam Split PCB Cover Bottom, Integrated Mount  52087.STL  Fits RunCam Split V1  52135  RunCam Split v2 PCB Top Cover  52135.STL  Fits RunCam Split V2  52134  RunCam Split v2 PCB Bottom Cover, Integrated Mount  52134.STL  Fits RunCam Split V2 Hardware 4x M3 x 10mm Philips Head Screw, Nylon 4x M2 x 5mm Button Head Screw (RunCam)

See Also

• 390 Degree Geared Pan and Tilt
• Forward Offset Pan & Tilt
• Heavy Duty Pan and Tilt
• Gimbals!

Comments? Questions?

• email me!