Difference between revisions of "Forward Offset Pan & Tilt"
From ItsQv
(→Introduction) |
|||
| Line 13: | Line 13: | ||
== Introduction == | == Introduction == | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:PNT03.jpg]] | ||
| + | |- | ||
| + | | align="center" | Base servo plate | ||
| + | |}<br><br> | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:PNT14.jpg]] | ||
| + | |- | ||
| + | | align="center" | Lower 'U' bracket | ||
| + | |}<br><br> | ||
| + | |||
| + | {| border="0" cellspacing="0" cellpadding="0" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:PNT15.jpg]] | ||
| + | |- | ||
| + | | align="center" | Camera Plate | ||
| + | |}<br><br> | ||
| + | |||
| + | === Parts List === | ||
| + | |||
| + | Servos & Hardware<br> | ||
| + | :2ea 9 gram x 2Kg Servos, 1 modified for 180 degree travel | ||
| + | :4ea M2x6 socket head cap screws | ||
| + | :4ea M2 flat washers | ||
| + | :4ea #1 x 1/8" flat head sheet metal screws | ||
| + | :Align PJ Gel Pad (optional) | ||
| + | :Small wire ties | ||
| + | |||
| + | 3D Prints | ||
| + | :Camera Mount Plate - PnT_Camera_Plate_v02 | ||
| + | :Yaw Bracket - PnT_Lower_Bracket_v02 | ||
| + | :Yaw Servo Mount Plate - PnT_Servo_Bracket | ||
| + | |||
| + | Tools needed | ||
| + | :1.5mm ball end driver (allen wrench) | ||
| + | :Phillips head screwdriver | ||
| + | :2mm tap and tap drill | ||
| + | |||
| + | Camera<br> | ||
| + | :Mobius with lens '2C' modified for vertical mount<br><br> | ||
| + | |||
| + | === Files === | ||
| + | |||
| + | Here are the print files if you would like to give this a try. The zip contains the printable pieces and image files, simply richt-click the link and select "Save Target" for the download. If you would like the native SolidWorks files, please drop me a line (below) and I will accomodate.<br><br> | ||
| + | |||
| + | [http://www.itsqv.com/share/Pan_and_Tilt_v1.zip Mobius Compact Pan and Tilt v1 ZIP] | ||
| + | <br><br> | ||
| + | |||
| + | === Comments? Questions? === | ||
| + | |||
| + | :'''<u>[mailto:qmar80@hotmail.com?Subject=About%20the%20Forward%20Offset%20Gimbal&body=Question? email me!]</u>''' | ||
| + | |||
| + | == See Also == | ||
| + | |||
| + | [[Forward Offset Pan & Tilt]] | ||
| + | |||
| + | <br><br><br> | ||
| + | [[Category:Contents]] | ||
Revision as of 09:30, 18 March 2016
|
This page or section is under construction and will change going forward.
Questions or Comments? Please contact the Wiki administrator |
February 2016
| |
| Simple 9g Servo Pan & Tilt |
Introduction
|
| Base servo plate |
| File:PNT14.jpg |
| Lower 'U' bracket |
| File:PNT15.jpg |
| Camera Plate |
Parts List
Servos & Hardware
- 2ea 9 gram x 2Kg Servos, 1 modified for 180 degree travel
- 4ea M2x6 socket head cap screws
- 4ea M2 flat washers
- 4ea #1 x 1/8" flat head sheet metal screws
- Align PJ Gel Pad (optional)
- Small wire ties
3D Prints
- Camera Mount Plate - PnT_Camera_Plate_v02
- Yaw Bracket - PnT_Lower_Bracket_v02
- Yaw Servo Mount Plate - PnT_Servo_Bracket
Tools needed
- 1.5mm ball end driver (allen wrench)
- Phillips head screwdriver
- 2mm tap and tap drill
Camera
- Mobius with lens '2C' modified for vertical mount
Files
Here are the print files if you would like to give this a try. The zip contains the printable pieces and image files, simply richt-click the link and select "Save Target" for the download. If you would like the native SolidWorks files, please drop me a line (below) and I will accomodate.
Mobius Compact Pan and Tilt v1 ZIP
Comments? Questions?
See Also
Forward Offset Pan & Tilt
