Difference between revisions of "Brushless Roll Gimbal"
From ItsQv
(→Print Parts) |
(→Electronics) |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 16: | Line 16: | ||
In this catalog of parts are components needed to make a brushless single axis roll gimbal. There are notes on compatibility and some pieces with sketches for more information. This roll gimbal fits both my Mini Talon & Stratosurfer canopies as well as any other flat plate mount.<br><br> | In this catalog of parts are components needed to make a brushless single axis roll gimbal. There are notes on compatibility and some pieces with sketches for more information. This roll gimbal fits both my Mini Talon & Stratosurfer canopies as well as any other flat plate mount.<br><br> | ||
| − | + | === Electronics === | |
| − | === | + | |
| − | + | '''Motors Used''' | |
| + | <br> | ||
| + | :* RCTimer GBM2804 hollow shaft Brushless Gimbal Motor (shown) | ||
| + | :* Multistar 1807-340Kv Brushless Gimbal Motor | ||
| + | <br> | ||
| − | + | '''Controllers Used''' | |
| − | + | <br> | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | :* Storm32 v1.1 Brushless Gimbal Controller | |
| − | :* | + | :* RTF Mini Brushless Gimbal Controller |
| − | :* | + | <br><br> |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | == Print Parts == | + | === Print Parts === |
<br> | <br> | ||
| Line 56: | Line 47: | ||
| align="Left" | Roll Mount Upright | | align="Left" | Roll Mount Upright | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52083.STL 52083.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52083.STL 52083.STL] | ||
| − | | align="Left" | | + | | align="Left" | 52083_Sketch |
| align="Left" | Fits canopies for Mini Talon and Stratosurfer. See part sketch for mount hole spacing. | | align="Left" | Fits canopies for Mini Talon and Stratosurfer. See part sketch for mount hole spacing. | ||
|- | |- | ||
| Line 63: | Line 54: | ||
| align="Left" | Motor mount, 16mm | | align="Left" | Motor mount, 16mm | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52013.STL 52013.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52013.STL 52013.STL] | ||
| − | | align="Left" | | + | | align="Left" | 52013_Sketch |
| align="Left" | Fits motors with 16mm bolt circle | | align="Left" | Fits motors with 16mm bolt circle | ||
|- | |- | ||
| Line 70: | Line 61: | ||
| align="Left" | Motor mount, 12mm | | align="Left" | Motor mount, 12mm | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52187.STL 52187.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52187.STL 52187.STL] | ||
| − | | align="Left" | | + | | align="Left" | 52187_Sketch |
| align="Left" | Fits motors with 12mm bolt circle | | align="Left" | Fits motors with 12mm bolt circle | ||
|- | |- | ||
| Line 77: | Line 68: | ||
| align="Left" | Camera plate | | align="Left" | Camera plate | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52011.STL 52011.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52011.STL 52011.STL] | ||
| − | | align="Left" | | + | | align="Left" | 52011_Sketch |
| align="Left" | Supports Mobius, Mini Mobius, RunCam, Runcam Split, etc. | | align="Left" | Supports Mobius, Mini Mobius, RunCam, Runcam Split, etc. | ||
|- | |- | ||
| Line 84: | Line 75: | ||
| align="Left" | Upright brace, long | | align="Left" | Upright brace, long | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/10036.STL 10036.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/10036.STL 10036.STL] | ||
| − | | align="Left" | | + | | align="Left" | 10036_Sketch |
| align="Left" | Fits Mini Talon rear mount canopy | | align="Left" | Fits Mini Talon rear mount canopy | ||
|- | |- | ||
| Line 91: | Line 82: | ||
| align="Left" | Upright brace, Short | | align="Left" | Upright brace, Short | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/10037.STL 10037.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/10037.STL 10037.STL] | ||
| − | | align="Left" | | + | | align="Left" | 10037_Sketch |
| align="Left" | Fits Mini Talon front mount canopy | | align="Left" | Fits Mini Talon front mount canopy | ||
|- | |- | ||
| Line 98: | Line 89: | ||
| align="Left" | Upright brace, Stratosurfer | | align="Left" | Upright brace, Stratosurfer | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/10038.STL 10038.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/10038.STL 10038.STL] | ||
| − | | align="Left" | | + | | align="Left" | 10038_Sketch |
| align="Left" | Fits Stratosurfer long LP canopy | | align="Left" | Fits Stratosurfer long LP canopy | ||
|- | |- | ||
| Line 105: | Line 96: | ||
| align="Left" | Upright tilt plate, 4 degree | | align="Left" | Upright tilt plate, 4 degree | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52184.STL 52184.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52184.STL 52184.STL] | ||
| − | | align="Left" | | + | | align="Left" | 52184_Sketch |
| align="Left" | Fits all 4-bolt canopy mounts | | align="Left" | Fits all 4-bolt canopy mounts | ||
|} | |} | ||
| Line 133: | Line 124: | ||
|- | |- | ||
| align="center" | [[File:SS161.JPG|700px]] | | align="center" | [[File:SS161.JPG|700px]] | ||
| + | |} | ||
| + | <br> | ||
| + | |||
| + | {| cellspacing="1" cellpadding="1" align="center" border="0" | ||
| + | |- | ||
| + | | align="center" | [[File:SS163.JPG|700px]] | ||
| + | |- | ||
| + | | align="center" | Canopy inside with Storm32 controller | ||
|} | |} | ||
<br><br> | <br><br> | ||
Latest revision as of 23:04, 26 November 2018
© Mark Qvale - November, 2018
| |
Introduction
In this catalog of parts are components needed to make a brushless single axis roll gimbal. There are notes on compatibility and some pieces with sketches for more information. This roll gimbal fits both my Mini Talon & Stratosurfer canopies as well as any other flat plate mount.
Electronics
Motors Used
- RCTimer GBM2804 hollow shaft Brushless Gimbal Motor (shown)
- Multistar 1807-340Kv Brushless Gimbal Motor
Controllers Used
- Storm32 v1.1 Brushless Gimbal Controller
- RTF Mini Brushless Gimbal Controller
Print Parts
| Image | Part Number | Part Description | Print File | Drawing | Compatibility |
|
52083 | Roll Mount Upright | 52083.STL | 52083_Sketch | Fits canopies for Mini Talon and Stratosurfer. See part sketch for mount hole spacing. |
|
52013 | Motor mount, 16mm | 52013.STL | 52013_Sketch | Fits motors with 16mm bolt circle |
|
52187 | Motor mount, 12mm | 52187.STL | 52187_Sketch | Fits motors with 12mm bolt circle |
|
52011 | Camera plate | 52011.STL | 52011_Sketch | Supports Mobius, Mini Mobius, RunCam, Runcam Split, etc. |
|
10036 | Upright brace, long | 10036.STL | 10036_Sketch | Fits Mini Talon rear mount canopy |
|
10037 | Upright brace, Short | 10037.STL | 10037_Sketch | Fits Mini Talon front mount canopy |
|
10038 | Upright brace, Stratosurfer | 10038.STL | 10038_Sketch | Fits Stratosurfer long LP canopy |
|
52184 | Upright tilt plate, 4 degree | 52184.STL | 52184_Sketch | Fits all 4-bolt canopy mounts |
Typical Assemblies
Details
|
Mini Talon Forward Mount
|
Stratosurfer Low Profile Mount
|
|
| Canopy inside with Storm32 controller |
See Also
Comments? Questions?
