Difference between revisions of "RunCam Split Camera Case"
From ItsQv
(→Print Parts) |
(→See Also) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | #REDIRECT [[RunCam_Split_Pan_and_Tilt_and_Cases]] | ||
| + | |||
<!--[[File:BTI.png|link=Current Parts Catalogs|Current Parts Catalogs]]<br>--> | <!--[[File:BTI.png|link=Current Parts Catalogs|Current Parts Catalogs]]<br>--> | ||
<i><small>© Mark Qvale - November, 2017</small></i><br> | <i><small>© Mark Qvale - November, 2017</small></i><br> | ||
| Line 12: | Line 14: | ||
==<br>Introduction == | ==<br>Introduction == | ||
| − | After picking up a Runcam Split camera I decided to create a case so that I | + | After picking up a Runcam Split V1 camera I decided to create a case so that I could easily move the camera from plane to plane. This article then shows three versions of this case. It includes a snap on/off cover over the SD Card to make it easy to access and an internal guard around the microphone to cut down on wind noise.<br> |
| + | |||
| + | '''NOTE: This was modeled to fit the V1 camera but you can also use it on the V2 version with a slight dremel tool modification.''' | ||
=== Versions === | === Versions === | ||
| Line 47: | Line 51: | ||
| align="Left" | '''52067''' | | align="Left" | '''52067''' | ||
| align="Left" | RunCam Split PCB Top Cover | | align="Left" | RunCam Split PCB Top Cover | ||
| − | | align=" | + | | align="Center" | 4.3g |
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52067.STL 52067.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52067.STL 52067.STL] | ||
| align="Left" | 52067_Sketch | | align="Left" | 52067_Sketch | ||
| Line 55: | Line 59: | ||
| align="Left" | '''52076''' | | align="Left" | '''52076''' | ||
| align="Left" | RunCam Split SD Card Snap Cover | | align="Left" | RunCam Split SD Card Snap Cover | ||
| − | | align=" | + | | align="Center" | 0.7g |
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52076.STL 52076.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52076.STL 52076.STL] | ||
| align="Left" | 52076_Sketch | | align="Left" | 52076_Sketch | ||
| Line 63: | Line 67: | ||
| align="Left" | '''52086''' | | align="Left" | '''52086''' | ||
| align="Left" | RunCam Split PCB Cover Bottom, Extended Mount | | align="Left" | RunCam Split PCB Cover Bottom, Extended Mount | ||
| − | | align=" | + | | align="Center" | 4.6g |
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52086.STL 52086.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52086.STL 52086.STL] | ||
| align="Left" | 52086_Sketch | | align="Left" | 52086_Sketch | ||
| Line 71: | Line 75: | ||
| align="Left" | '''52087''' | | align="Left" | '''52087''' | ||
| align="Left" | RunCam Split PCB Cover Bottom, Integrated Mount | | align="Left" | RunCam Split PCB Cover Bottom, Integrated Mount | ||
| − | | align=" | + | | align="Center" | 4.5g |
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52087.STL 52087.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52087.STL 52087.STL] | ||
| align="Left" | 52087_Sketch | | align="Left" | 52087_Sketch | ||
| Line 79: | Line 83: | ||
| align="Left" | '''52088''' | | align="Left" | '''52088''' | ||
| align="Left" | RunCam Split PCB Cover Bottom, Standard Mount | | align="Left" | RunCam Split PCB Cover Bottom, Standard Mount | ||
| − | | align=" | + | | align="Center" | 3.1g |
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52088.STL 52088.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52088.STL 52088.STL] | ||
| align="Left" | 52088_Sketch | | align="Left" | 52088_Sketch | ||
| Line 101: | Line 105: | ||
<br><br><br> | <br><br><br> | ||
| − | [[CATEGORY: | + | [[CATEGORY:Marks]] |
Latest revision as of 13:50, 18 March 2018
Redirect to:
© Mark Qvale - November, 2017
| |
Introduction
After picking up a Runcam Split V1 camera I decided to create a case so that I could easily move the camera from plane to plane. This article then shows three versions of this case. It includes a snap on/off cover over the SD Card to make it easy to access and an internal guard around the microphone to cut down on wind noise.
NOTE: This was modeled to fit the V1 camera but you can also use it on the V2 version with a slight dremel tool modification.
Versions
The three versions are shown below. They all use the same top cover.
|
You will need to have an M3 tap to set-up the top and bottom.
|
Print Parts
| Image | Part Number | Part Description | Weight | Print File | Drawing | Compatibility |
|
52067 | RunCam Split PCB Top Cover | 4.3g | 52067.STL | 52067_Sketch | Fits RunCam Split V1 |
|
52076 | RunCam Split SD Card Snap Cover | 0.7g | 52076.STL | 52076_Sketch | Fits 52067 Cover. |
|
52086 | RunCam Split PCB Cover Bottom, Extended Mount | 4.6g | 52086.STL | 52086_Sketch | Fits RunCam Split V1 |
|
52087 | RunCam Split PCB Cover Bottom, Integrated Mount | 4.5g | 52087.STL | 52087_Sketch | Fits RunCam Split V1 |
|
52088 | RunCam Split PCB Cover Bottom, Standard Mount | 3.1g | 52088.STL | 52088_Sketch | Fits RunCam Split V1 |
See Also
- TBA
Project 3D Print Files
This project can also be found on Thingiverse - RunCam Split Simple Case & Mount
Comments? Questions?
- <u>email me!
