Difference between revisions of "3D Parts"
From ItsQv
(→Antenna SMA Connector Wrench) |
(→Battery Strap Guide) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 12: | Line 12: | ||
These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and will effectively stop the blades from over crossing and over extending.<br><br> | These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and will effectively stop the blades from over crossing and over extending.<br><br> | ||
| − | {| border="0" cellspacing="1" cellpadding="1 | + | {| border="0" cellspacing="1" cellpadding="1" align="center" |
|- | |- | ||
| align="center" | [[File:FPA054.jpg|500px]] | | align="center" | [[File:FPA054.jpg|500px]] | ||
| Line 19: | Line 19: | ||
| − | {| border="1" cellspacing="1" cellpadding="1 | + | {| border="1" cellspacing="1" cellpadding="1" align="left" |
|- | |- | ||
| − | | align="Left" | '''Part Number''' | + | | width="100" align="Left" | '''Part Number''' |
| − | | align="Left" | '''Part Description''' | + | | width="400" align="Left" | '''Part Description''' |
| − | | align="Center" | '''Yoke Size''' | + | | width="80" align="Center" | '''Yoke Size''' |
| − | | align="Center" | '''Drawing''' | + | | width="100" align="Center" | '''Drawing''' |
| − | | align="Center" | '''Print File''' | + | | width="100" align="Center" | '''Print File''' |
|- | |- | ||
| align="Left" | '''10001''' | | align="Left" | '''10001''' | ||
| Line 63: | Line 63: | ||
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10006.STL 10006.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10006.STL 10006.STL] | ||
|} | |} | ||
| + | {{Clear1}} | ||
| − | '''Print Recomendations''' | + | '''Print Recomendations''' |
| − | ABS is best as it is UV tolerant. They fit and work fine on 0.2mm resolution and moderate print speed. | + | : ABS is best as it is UV tolerant. They fit and work fine on 0.2mm resolution and moderate print speed. |
| − | + | <br> | |
'''See Also''' | '''See Also''' | ||
| Line 114: | Line 115: | ||
---- | ---- | ||
| + | === Battery Strap Guide === | ||
| + | ---- | ||
| + | <i>Release - October, 2016</i> | ||
| + | <br> | ||
| + | This strap guide is embedded in the bottom fuselage foam outside as a way to add strength to the pack hold down system. Having this also gives the ability to easily adjust or replace the strap.<br><br> | ||
| + | |||
| + | {| border="0" cellspacing="1" cellpadding="1" width="95%" align="center" | ||
| + | |- | ||
| + | | align="center" | [[File:10015.jpg|900px]] | ||
| + | |} | ||
| + | <br><br> | ||
| + | |||
| + | {| border="1" cellspacing="1" cellpadding="1" align="left" | ||
| + | |- | ||
| + | | width="100" align="Left" | '''Part Number''' | ||
| + | | width="400" align="Left" | '''Part Description''' | ||
| + | | width="100" align="Center" | '''Drawing''' | ||
| + | | width="100" align="Center" | '''Print File''' | ||
| + | |- | ||
| + | | align="Left" | '''10015''' | ||
| + | | align="Left" | Battery strap guide well, 35mm | ||
| + | | align="Center" | - | ||
| + | | align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10015.STL 10015.STL] | ||
| + | |- | ||
| + | | align="Left" | '''10016''' | ||
| + | | align="Left" | Battery strap guide well, 35mm | ||
| + | | align="Center" | - | ||
| + | | align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10016.STL 10016.STL] | ||
| + | |- | ||
| + | | align="Left" | '''10017''' | ||
| + | | align="Left" | Battery strap guide well, 35mm | ||
| + | | align="Center" | - | ||
| + | | align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10017.STL 10017.STL] | ||
| + | |} | ||
| + | {{Clear1}} | ||
| + | |||
| + | '''Install''' | ||
| + | |||
| + | : Find the correct placement by balancing the plane with the pack. On the outside of the fuse remove just enough foam to install the part so its flanges are flush to the foam. Use E6000, Beacons FoamTac or UHU-POR glue to fasten in place then hotwire the slots for the straps. | ||
| + | <br> | ||
| + | |||
| + | '''Print Recomendations''' | ||
| + | |||
| + | : ABS or PLA works well for this part. It will fit and work fine on 0.2mm resolution and moderate print speed. | ||
| + | <br> | ||
| + | |||
| + | '''See Also''' | ||
| + | |||
| + | : Project pages - None<br><br> | ||
| + | |||
| + | ---- | ||
<br><br><br> | <br><br><br> | ||
| − | [[Category: | + | [[Category:Parts]] |
Latest revision as of 20:33, 27 March 2018
January 2017
Contents
GENERAL PARTS
Aeronaut Folding Propeller Stop Insert
Release - May 2016
These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and will effectively stop the blades from over crossing and over extending.
|
| Part Number | Part Description | Yoke Size | Drawing | Print File |
| 10001 | Propeller stop insert, 38mm x 5mm | 38mm | 10001.PDF | 10001.STL |
| 10002 | Propeller stop insert, 38mm x 6mm | 38mm | - | 10002.STL |
| 10003 | Propeller stop insert, 38mm x 8mm | 38mm | - | 10003.STL |
| 10004 | Propeller stop insert, 42mm x 5mm | 42mm | - | 10004.STL |
| 10005 | Propeller stop insert, 42mm x 6mm | 42mm | - | 10005.STL |
| 10006 | Propeller stop insert, 42mm x 8mm | 42mm | - | 10006.STL |
Print Recomendations
- ABS is best as it is UV tolerant. They fit and work fine on 0.2mm resolution and moderate print speed.
See Also
- Project pages - How To - Set-Up a Pusher Style Folding Prop
Antenna SMA Connector Wrench
Release - March, 2016
This is used to loosen or tighten an SMA connector nut that is burried and difficult to get to with a standard wrench or pliers. It is like a flare nut wrench in that you can fit it oveer the coax and slide it down to engage the nut.
|
| Part Number | Part Description | Drawing | Print File |
| 10012 | Thumb "flare-nut" wrench for SMA antenna connectors | - | 10012.STL |
Print Recomendations
- PLA works well for this part. They fit and work fine on 0.2mm resolution and moderate print speed.
See Also
- Project pages - None
Battery Strap Guide
Release - October, 2016
This strap guide is embedded in the bottom fuselage foam outside as a way to add strength to the pack hold down system. Having this also gives the ability to easily adjust or replace the strap.
|
| Part Number | Part Description | Drawing | Print File |
| 10015 | Battery strap guide well, 35mm | - | 10015.STL |
| 10016 | Battery strap guide well, 35mm | - | 10016.STL |
| 10017 | Battery strap guide well, 35mm | - | 10017.STL |
Install
- Find the correct placement by balancing the plane with the pack. On the outside of the fuse remove just enough foam to install the part so its flanges are flush to the foam. Use E6000, Beacons FoamTac or UHU-POR glue to fasten in place then hotwire the slots for the straps.
Print Recomendations
- ABS or PLA works well for this part. It will fit and work fine on 0.2mm resolution and moderate print speed.
See Also
- Project pages - None
