Difference between revisions of "TEST 0132"
From ItsQv
(→Intro) |
(→Full Length Low Profile Canopies) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 10: | Line 10: | ||
|- | |- | ||
| align="center" | [[File:LPC01.JPG|600px]] | | align="center" | [[File:LPC01.JPG|600px]] | ||
| + | |- | ||
| + | | align="center" | Two piece swoopiness! | ||
|} | |} | ||
<br><br> | <br><br> | ||
| − | Below are the parts to put together a | + | Below are the parts to put together a one-piece full length canopy or a two-piece full length canopy (shown above). There is also a short list of a few Pan & Tilt parts to fit the PnT mount shown. If you elect to go with the full length, one piece canopy, you will need the ability to print quality, large parts on a print bed of 200mm x 200mm minimum. These canopies work with the tall, printed single motor set-up or the twin motor set-up.<br><br> |
{| border="0" cellspacing="1" cellpadding="1" align="center" | {| border="0" cellspacing="1" cellpadding="1" align="center" | ||
| Line 21: | Line 23: | ||
<br> | <br> | ||
| − | {| border="0" cellspacing="1" cellpadding="1" align="center" | + | <!--{| border="0" cellspacing="1" cellpadding="1" align="center" |
|- | |- | ||
| align="center" | [[File:LPC05.JPG|600px]] | | align="center" | [[File:LPC05.JPG|600px]] | ||
| − | |}<br><br> | + | |}<br><br>--> |
All parts shown below have been test printed in PLA at .2mm resolution and weights shown are estimates. | All parts shown below have been test printed in PLA at .2mm resolution and weights shown are estimates. | ||
Latest revision as of 17:52, 29 July 2020
Intro
Mark Qvale - March, 2020
Full Length Low Profile Canopies
|
| Two piece swoopiness! |
Below are the parts to put together a one-piece full length canopy or a two-piece full length canopy (shown above). There is also a short list of a few Pan & Tilt parts to fit the PnT mount shown. If you elect to go with the full length, one piece canopy, you will need the ability to print quality, large parts on a print bed of 200mm x 200mm minimum. These canopies work with the tall, printed single motor set-up or the twin motor set-up.
|
All parts shown below have been test printed in PLA at .2mm resolution and weights shown are estimates.
| Image | Part Number | Part Description | Weight | Print File | Compatibility Notes |
|
52238 | Full Length, Low Profile Canopy, Plain | 64g | 52238.STL | Needs 52246 Low Profile Front Wing Mount, Latching (below) |
|
52239 | Full Length, Low Profile Canopy, for PnT | 67g | 52239.STL | Needs 52246 Low Profile Front Wing Mount, Latching (below) |
|
52240 | Full Length, 2PC Front Low Profile, Plain | 42g | 52240.STL | Plain front section. Cut-to-fit your camera(s) |
|
52241 | Full Length, 2PC Front Low Profile, PnT | 44g | 52241.STL | Front section with PnT 4 bolt mount |
|
52242 | Full Length, 2PC Rear Low Profile Canopy | 28g | 52242.STL | Fits both front sections, 52240 & 52241 |
|
52243 | Full Length, Low Profile Canopy, Front Mount | 2.5g | 52243.STL | Front mount for the 52238, 52239, 52240 & 52241 canopies |
|
52244 | Full Length, Low Profile Canopy, Front Mount Nut Plate | 1.8g | 52244.STL | Nut plate for front mount piece |
|
52245 | Low Profile Front Wing Mount, Plain | 15g | 52245.STL | For use with the 2 piece canopy (no latch) |
|
52246 | Low Profile Front Wing Mount, Latching | 15g | 52246.STL | Can be used for either 1 piece or 2 piece canopies |
|
52247 | Glue-In VTx mount | 7g | 52247.STL | See Mount Drawing for position information |
|
