Difference between revisions of "TEST 0132"
From ItsQv
(→Full Length Low Profile Canopies) |
(→Full Length Low Profile Canopies) |
||
| Line 6: | Line 6: | ||
=== Full Length Low Profile Canopies === | === Full Length Low Profile Canopies === | ||
| − | + | <br> | |
{| border="0" cellspacing="1" cellpadding="1" align="center" | {| border="0" cellspacing="1" cellpadding="1" align="center" | ||
|- | |- | ||
| Line 99: | Line 99: | ||
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52246.STL 52246.STL] | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52246.STL 52246.STL] | ||
| align="Left" | Can be used for either 1 piece or 2 piece canopies | | align="Left" | Can be used for either 1 piece or 2 piece canopies | ||
| + | |- | ||
| + | | align="Left" | [[File:52247sm.JPG]] | ||
| + | | align="Left" | '''52247''' | ||
| + | | align="Left" | Glue-In VTx mount | ||
| + | | align="Left" | 7g | ||
| + | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52247.STL 52247.STL] | ||
| + | | align="Left" | See Mount Drawing for position information | ||
|} | |} | ||
{{Clear1}} | {{Clear1}} | ||
[[Category:Marks]] | [[Category:Marks]] | ||
Revision as of 21:12, 28 July 2020
Intro
Mark Qvale - March, 2020
Full Length Low Profile Canopies
|
If you have the ability to print quality large parts and you have a print bed of 200mm x 200mm with print height of 170mm minimum, you can have the nicest, most aerodynamic canopy setup. These canopies work with the tall, printed single motor set-up or the twin motor set-up.
All parts were test printed in PLA at .2mm resolution. Weights shown are estimates
|
| 600px |
| Image | Part Number | Part Description | Weight | Print File | Compatibility Notes |
|
52238 | Full Length, Low Profile Canopy, Plain | 64g | 52238.STL | Needs 52246 Low Profile Front Wing Mount, Latching (below) |
|
52239 | Full Length, Low Profile Canopy, for PnT | 67g | 52239.STL | Needs 52246 Low Profile Front Wing Mount, Latching (below) |
|
52240 | Full Length, 2PC Front Low Profile, Plain | 42g | 52240.STL | Plain front section. Cut-to-fit your camera(s) |
|
52241 | Full Length, 2PC Front Low Profile, PnT | 44g | 52241.STL | Front section with PnT 4 bolt mount |
|
52242 | Full Length, 2PC Rear Low Profile Canopy | 28g | 52242.STL | Fits both front sections, 52240 & 52241 |
|
52243 | Full Length, Low Profile Canopy, Front Mount | 2.5g | 52243.STL | Front mount for the 52238, 52239, 52240 & 52241 canopies |
|
52244 | Full Length, Low Profile Canopy, Front Mount Nut Plate | 1.8g | 52244.STL | Nut plate for front mount piece |
|
52245 | Low Profile Front Wing Mount, Plain | 15g | 52245.STL | For use with the 2 piece canopy (no latch) |
|
52246_ | Low Profile Front Wing Mount, Latching | 15g | 52246.STL | Can be used for either 1 piece or 2 piece canopies |
|
52247 | Glue-In VTx mount | 7g | 52247.STL | See Mount Drawing for position information |
