Difference between revisions of "Grom Audio Toyota Microphone Mount"
(Created page with "<i><small>© Mark Qvale - October, 2018</small></i><br> {| cellspacing="1" cellpadding="1" width="95%" border="0" |- | align="left" valign="top" width="30%" | __TOC__ | align...") |
(→Introduction) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
==<br>Introduction == | ==<br>Introduction == | ||
| − | I bought a Grom Audio bluetooth module for my 2007 Toyota 4Runner and while the unit itself is excellent, I decided I didn't like the microphone mount. I've installed similar microphone mounts in the past and always found them to be unreliable | + | I bought a Grom Audio bluetooth module for my 2007 Toyota 4Runner and while the unit itself is excellent, I decided I didn't like the microphone mount. I've installed similar microphone mounts in the past and always found them to be unreliable. Where I live in Southern Nevada we see inside vehicle temperatures of 150°F (65°C) or more as a common occurrence in the summer. Simply put, the double sided tape just disintegrates. |
<br> | <br> | ||
| − | This then is a small project to | + | This then is a small project to create a 3D printed part to mount the microphone in a more permanent piece with a more "factory" look.<br><br> |
=== Part Design === | === Part Design === | ||
| Line 23: | Line 23: | ||
{| border="0" cellspacing="1" cellpadding="1" align="center" | {| border="0" cellspacing="1" cellpadding="1" align="center" | ||
|- | |- | ||
| − | | align="center" | [[File:tmm1.JPG| | + | | align="center" | [[File:tmm1.JPG|500px]] |
| − | | | + | |- |
| − | | align="center" | | + | | align="center" | Printed part and blank cover |
|} | |} | ||
<br> | <br> | ||
| Line 31: | Line 31: | ||
{| border="0" cellspacing="1" cellpadding="1" align="center" | {| border="0" cellspacing="1" cellpadding="1" align="center" | ||
|- | |- | ||
| − | | align="center" | [[File:tmm6.gif| | + | | align="center" | [[File:tmm6.gif|400px]] |
| − | + | ||
| − | + | ||
|} | |} | ||
<br> | <br> | ||
| Line 40: | Line 38: | ||
|- | |- | ||
| align="center" | [[File:tmm7.JPG|600px]] | | align="center" | [[File:tmm7.JPG|600px]] | ||
| − | | | + | |- |
| align="center" | Part sketch | | align="center" | Part sketch | ||
|} | |} | ||
| Line 57: | Line 55: | ||
{| border="0" cellspacing="1" cellpadding="1" align="center" | {| border="0" cellspacing="1" cellpadding="1" align="center" | ||
|- | |- | ||
| − | | align="center" | [[File:tmm4. | + | | align="center" | [[File:tmm4.jpg|700px]] |
| − | + | ||
| − | + | ||
|} | |} | ||
<br><br> | <br><br> | ||
| + | |||
| + | === Print Service === | ||
| + | |||
| + | To get this part made quickly and cheaply you can contact [https://www.3dhubs.com 3DHubs.com]. They do an excellent job of setting you up with a local printer and their prices are usually quite good.<br><br> | ||
== See Also == | == See Also == | ||
Latest revision as of 22:18, 28 October 2018
© Mark Qvale - October, 2018
| |
Introduction
I bought a Grom Audio bluetooth module for my 2007 Toyota 4Runner and while the unit itself is excellent, I decided I didn't like the microphone mount. I've installed similar microphone mounts in the past and always found them to be unreliable. Where I live in Southern Nevada we see inside vehicle temperatures of 150°F (65°C) or more as a common occurrence in the summer. Simply put, the double sided tape just disintegrates.
This then is a small project to create a 3D printed part to mount the microphone in a more permanent piece with a more "factory" look.
Part Design
I modeled the part after one of the blank snap-in switch covers. The microphone slides into the back of the piece and is held in by a slight interference fit and a couple tiny dabs of hot glue which also makes it easily removable. It is angled up 15 degrees so that it is essentially pointed at the driver
|
| Printed part and blank cover |
|
|
| Part sketch |
Print Setup
This piece, as shown, is printed in black ABS at a print resolution of 0.1mm. It is sliced and printed on its side with a support structure set up as follows:
- Slicer - Cura
- Overhang Angle - 70°
- Support infill - 24%
Here is a picture of how it looks in Cura:
|
Print Service
To get this part made quickly and cheaply you can contact 3DHubs.com. They do an excellent job of setting you up with a local printer and their prices are usually quite good.
See Also
3D Print File
Comments? Questions?
