Difference between revisions of "3D Parts"

From ItsQv
Jump to: navigation, search
(→‎Aeronaut Folding Propeller Stop Insert)
(→‎Battery Strap Guide)
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
3D Parts
+
<i>January 2017</i><br><br>
 +
__TOC__
 
<br><br>
 
<br><br>
  
−
== Aeronaut Folding Propeller Stop Insert ==
+
== GENERAL PARTS ==
  
−
These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and stop the blades from over crossing and over extending.<br><br>
+
=== Aeronaut Folding Propeller Stop Insert ===
 +
----
 +
<i>Release - May 2016</i>
 +
<br>
  
−
{| border="0" cellspacing="1" cellpadding="1" width="95%" align="center"
+
These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and will effectively stop the blades from over crossing and over extending.<br><br>
 +
 
 +
{| border="0" cellspacing="1" cellpadding="1" align="center"
 
|-
 
|-
−
| align="center" | [[File:FPA054.jpg|800px]]
+
| align="center" | [[File:FPA054.jpg|500px]]
 
|}
 
|}
 
<br><br>
 
<br><br>
  
−
<!--
 
−
{| border="0" cellspacing="1" cellpadding="1" width="95%" align="center"
 
−
|-
 
−
| align="center" | [[File:FPA053.jpg|800px]]
 
−
|}
 
−
-->
 
  
−
{| border="1" cellspacing="1" cellpadding="1" width="95%" align="center"
+
{| border="1" cellspacing="1" cellpadding="1" align="left"
 
|-
 
|-
−
| align="Left" | Part Number
+
| width="100" align="Left" | '''Part Number'''
−
| align="Left" | Part Description
+
| width="400" align="Left" | '''Part Description'''
−
| align="Center" | Yoke Size
+
| width="80" align="Center" | '''Yoke Size'''
−
| align="Center" | Drawing
+
| width="100" align="Center" | '''Drawing'''
−
| align="Center" | Print File
+
| width="100" align="Center" | '''Print File'''
−
| align="Center" | Release Date
+
 
|-
 
|-
−
| align="Left" | 10001
+
| align="Left" | '''10001'''
 
| align="Left" | Propeller stop insert, 38mm x 5mm
 
| align="Left" | Propeller stop insert, 38mm x 5mm
 
| align="Center" | 38mm
 
| align="Center" | 38mm
−
| align="Center" | 10001.PDF
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10001.PDF 10001.PDF]
−
| align="Center" | 10001.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10001.STL 10001.STL]
−
| align="Center" | May 2016
+
 
|-
 
|-
−
| align="Left" | 10002
+
| align="Left" | '''10002'''
 
| align="Left" | Propeller stop insert, 38mm x 6mm
 
| align="Left" | Propeller stop insert, 38mm x 6mm
 
| align="Center" | 38mm
 
| align="Center" | 38mm
−
| align="Center" | 10002.PDF
+
| align="Center" | -
−
| align="Center" | 10002.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10002.STL 10002.STL]
−
| align="Center" | May 2016
+
 
|-
 
|-
−
| align="Left" | 10003
+
| align="Left" | '''10003'''
 
| align="Left" | Propeller stop insert, 38mm x 8mm
 
| align="Left" | Propeller stop insert, 38mm x 8mm
 
| align="Center" | 38mm
 
| align="Center" | 38mm
−
| align="Center" | 10003.PDF
+
| align="Center" | -
−
| align="Center" | 10003.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10003.STL 10003.STL]
−
| align="Center" | May 2016
+
 
|-
 
|-
−
| align="Left" | 10004
+
| align="Left" | '''10004'''
 
| align="Left" | Propeller stop insert, 42mm x 5mm
 
| align="Left" | Propeller stop insert, 42mm x 5mm
 
| align="Center" | 42mm
 
| align="Center" | 42mm
−
| align="Center" | 10004.PDF
+
| align="Center" | -
−
| align="Center" | 10004.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10004.STL 10004.STL]
−
| align="Center" | May 2016
+
 
|-
 
|-
−
| align="Left" | 10005
+
| align="Left" | '''10005'''
 
| align="Left" | Propeller stop insert, 42mm x 6mm
 
| align="Left" | Propeller stop insert, 42mm x 6mm
 
| align="Center" | 42mm
 
| align="Center" | 42mm
−
| align="Center" | 10005.PDF
+
| align="Center" | -
−
| align="Center" | 10005.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10005.STL 10005.STL]
−
| align="Center" | May 2016
+
 
|-
 
|-
−
| align="Left" | 10006
+
| align="Left" | '''10006'''
 
| align="Left" | Propeller stop insert, 42mm x 8mm
 
| align="Left" | Propeller stop insert, 42mm x 8mm
 
| align="Center" | 42mm
 
| align="Center" | 42mm
−
| align="Center" | 10006.PDF
+
| align="Center" | -
−
| align="Center" | 10006.STL
+
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10006.STL 10006.STL]
−
| align="Center" | May 2016
+
 
|}
 
|}
 +
{{Clear1}}
 +
 +
 +
'''Print Recomendations'''
 +
 +
: ABS is best as it is UV tolerant. They fit and work fine on 0.2mm resolution and moderate print speed.
 +
<br>
 +
 +
'''See Also'''
 +
 +
: Project pages - [[How To - Set-Up a Pusher Style Folding Prop]]<br><br>
 +
 +
----
 +
 +
=== Antenna SMA Connector Wrench ===
 +
----
 +
<i>Release - March, 2016</i>
 +
<br>
 +
 +
This is used to loosen or tighten an SMA connector nut that is burried and difficult to get to with a standard wrench or pliers. It is like a flare nut wrench in that you can fit it oveer the coax and slide it down to engage the nut.<br><br>
 +
 +
{| border="0" cellspacing="1" cellpadding="1" width="95%" align="center"
 +
|-
 +
| align="center" | [[File:10012.JPG|500px]]
 +
|}
 +
<br><br>
 +
 +
{| border="1" cellspacing="1" cellpadding="1" align="left"
 +
|-
 +
| width="100" align="Left" | '''Part Number'''
 +
| width="400" align="Left" | '''Part Description'''
 +
| width="100" align="Center" | '''Drawing'''
 +
| width="100" align="Center" | '''Print File'''
 +
|-
 +
| align="Left" | '''10012'''
 +
| align="Left" | Thumb "flare-nut" wrench for SMA antenna connectors
 +
| align="Center" | -
 +
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10012.STL 10012.STL]
 +
|}
 +
{{Clear1}}
 +
 +
 +
'''Print Recomendations'''
 +
 +
: PLA works well for this part. They fit and work fine on 0.2mm resolution and moderate print speed.
 +
<br><br>
 +
 +
'''See Also'''
 +
 +
: Project pages - None<br><br>
 +
 +
----
 +
=== Battery Strap Guide ===
 +
----
 +
<i>Release - October, 2016</i>
 +
<br>
 +
 +
This strap guide is embedded in the bottom fuselage foam outside as a way to add strength to the pack hold down system. Having this also gives the ability to easily adjust or replace the strap.<br><br>
 +
 +
{| border="0" cellspacing="1" cellpadding="1" width="95%" align="center"
 +
|-
 +
| align="center" | [[File:10015.jpg|900px]]
 +
|}
 +
<br><br>
 +
 +
{| border="1" cellspacing="1" cellpadding="1" align="left"
 +
|-
 +
| width="100" align="Left" | '''Part Number'''
 +
| width="400" align="Left" | '''Part Description'''
 +
| width="100" align="Center" | '''Drawing'''
 +
| width="100" align="Center" | '''Print File'''
 +
|-
 +
| align="Left" | '''10015'''
 +
| align="Left" | Battery strap guide well, 35mm
 +
| align="Center" | -
 +
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10015.STL 10015.STL]
 +
|-
 +
| align="Left" | '''10016'''
 +
| align="Left" | Battery strap guide well, 35mm
 +
| align="Center" | -
 +
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10016.STL 10016.STL]
 +
|-
 +
| align="Left" | '''10017'''
 +
| align="Left" | Battery strap guide well, 35mm
 +
| align="Center" | -
 +
| align="Center" | [http://www.itsqv.com/QVM/files/partdwg/10017.STL 10017.STL]
 +
|}
 +
{{Clear1}}
 +
 +
'''Install'''
 +
 +
: Find the correct placement by balancing the plane with the pack. On the outside of the fuse remove just enough foam to install the part so its flanges are flush to the foam. Use E6000, Beacons FoamTac or UHU-POR glue to fasten in place then hotwire the slots for the straps.
 +
<br>
 +
 +
'''Print Recomendations'''
  
 +
: ABS or PLA works well for this part. It will fit and work fine on 0.2mm resolution and moderate print speed.
 +
<br>
  
−
=== See Also ===
+
'''See Also'''
  
−
: Project pages - [[How To - Set-Up a Pusher Style Folding Prop]]
+
: Project pages - None<br><br>
  
 +
----
  
 
<br><br><br>
 
<br><br><br>
−
[[Category:Catalog]]
+
[[Category:Parts]]

Latest revision as of 20:33, 27 March 2018

January 2017



GENERAL PARTS

Aeronaut Folding Propeller Stop Insert

Release - May 2016

These inserts fit into a bare Aeronaut aluminum folding propeller yoke, also know as the "Center Piece". They are designed to be used in a pusher prop set-up and will effectively stop the blades from over crossing and over extending.

FPA054.jpg




Part Number Part Description Yoke Size Drawing Print File
10001 Propeller stop insert, 38mm x 5mm 38mm 10001.PDF 10001.STL
10002 Propeller stop insert, 38mm x 6mm 38mm - 10002.STL
10003 Propeller stop insert, 38mm x 8mm 38mm - 10003.STL
10004 Propeller stop insert, 42mm x 5mm 42mm - 10004.STL
10005 Propeller stop insert, 42mm x 6mm 42mm - 10005.STL
10006 Propeller stop insert, 42mm x 8mm 42mm - 10006.STL



Print Recomendations

ABS is best as it is UV tolerant. They fit and work fine on 0.2mm resolution and moderate print speed.


See Also

Project pages - How To - Set-Up a Pusher Style Folding Prop

Antenna SMA Connector Wrench

Release - March, 2016

This is used to loosen or tighten an SMA connector nut that is burried and difficult to get to with a standard wrench or pliers. It is like a flare nut wrench in that you can fit it oveer the coax and slide it down to engage the nut.

10012.JPG



Part Number Part Description Drawing Print File
10012 Thumb "flare-nut" wrench for SMA antenna connectors - 10012.STL



Print Recomendations

PLA works well for this part. They fit and work fine on 0.2mm resolution and moderate print speed.



See Also

Project pages - None

Battery Strap Guide

Release - October, 2016

This strap guide is embedded in the bottom fuselage foam outside as a way to add strength to the pack hold down system. Having this also gives the ability to easily adjust or replace the strap.

10015.jpg



Part Number Part Description Drawing Print File
10015 Battery strap guide well, 35mm - 10015.STL
10016 Battery strap guide well, 35mm - 10016.STL
10017 Battery strap guide well, 35mm - 10017.STL


Install

Find the correct placement by balancing the plane with the pack. On the outside of the fuse remove just enough foam to install the part so its flanges are flush to the foam. Use E6000, Beacons FoamTac or UHU-POR glue to fasten in place then hotwire the slots for the straps.


Print Recomendations

ABS or PLA works well for this part. It will fit and work fine on 0.2mm resolution and moderate print speed.


See Also

Project pages - None




Retrieved from "http://www.itsqv.com/QVM/index.php?title=3D_Parts&oldid=4195"