|
|
| (56 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | {{UnderConst}}
| + | #REDIRECT [[Parts_Catalog_-_Mini_Talon]] |
| − | <br><br>
| + | |
| | | | |
| − | <i>March, 2017</i>
| + | [[Category:Parts]] |
| − | {| cellspacing="1" cellpadding="1" width="95%" border="0"
| + | |
| − | |-
| + | |
| − | | align="left" valign="bottom" width="30%" | __TOC__
| + | |
| − | | align="right" width="70%" | [[File:Parts_.jpg|700px]]
| + | |
| − | |-
| + | |
| − | |
| + | |
| − | | align="right" width="50%" | Ready for printing!
| + | |
| − | |}
| + | |
| − | | + | |
| − | ==<br>Introduction ==
| + | |
| − | | + | |
| − | This article is a collection of 3D print parts specifically designed to fit the X-UAV Mini Talon. These have all been printed and most have been flight tested and even a few - crash tested :).<br><br>
| + | |
| − | | + | |
| − | Enjoy - Mark<br><br>
| + | |
| − | | + | |
| − | == Canopy's and Set-ups ==
| + | |
| − | | + | |
| − | I have redone the feature set that makes up this 3D model smoothing out the surface and profile and changing the NACA style vent to side air scoop type vents. It prints more cleanly now and I have added a version which will support either the Geared Pan & Tilt or the 390deg Pan & Tilt. Below you will find the latest versions of this fun design with downloads for all the printable STL files.<br><br>
| + | |
| − | | + | |
| − | === Plain Canopy ===
| + | |
| − | | + | |
| − | If you want to simply cover the nose for a more appealing look or need something to fit to your own structure this may be the part you want. The two FPV camera mounts are optional.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1001.jpg|800px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47001T.jpg]]
| + | |
| − | | align="Left" | '''47001'''
| + | |
| − | | align="Left" | Canopy, Plain
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47001.STL 47001.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52001.jpg]]
| + | |
| − | | align="Left" | '''52001'''
| + | |
| − | | align="Left" | Canopy support, front
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52001.STL 52001.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52002.jpg]]
| + | |
| − | | align="Left" | '''52002'''
| + | |
| − | | align="Left" | Canopy support, rear
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52002.STL 52002.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52004.jpg]]
| + | |
| − | | align="Left" | '''52004'''
| + | |
| − | | align="Left" | Optional HS1177 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52004.STL 52004.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52005.jpg]]
| + | |
| − | | align="Left" | '''52005'''
| + | |
| − | | align="Left" | Optional HS1184 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52005.STL 52005.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Hardware Shown'''<br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Quantity'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Philips head machine screw, M3 x 8mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Socket head cap screw, M3 x 10mm, Steel
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front support and rear catch in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br><br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | === Static Camera Mounts ===
| + | |
| − | | + | |
| − | This version has a cut-out and platform for the Mobius style HD cams and is the most aerodynamic of all the camera mount units. There are two different canopies, one specifically for the Mobius Mini and one which will accomodate either the Mobius or Runcam cameras.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1002.jpg|500px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47003T.jpg]]
| + | |
| − | | align="Left" | '''47003'''
| + | |
| − | | align="Left" | Canopy, Mobius Mini
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47003.STL 47003.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47005T.jpg]]
| + | |
| − | | align="Left" | '''47005'''
| + | |
| − | | align="Left" | Canopy, Mobius/Runcam
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47005.STL 47005.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54002.jpg]]
| + | |
| − | | align="Left" | '''54002'''
| + | |
| − | | align="Left" | Front deck plate, narrow
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54002.STL 54002.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54001.jpg]]
| + | |
| − | | align="Left" | '''54001'''
| + | |
| − | | align="Left" | Rear deck plate, narrow
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54001.STL 54001.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52006.jpg]]
| + | |
| − | | align="Left" | '''52006'''
| + | |
| − | | align="Left" | Deck plate support rib
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52006.STL 52006.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52007.jpg]]
| + | |
| − | | align="Left" | '''52007'''
| + | |
| − | | align="Left" | HD camera mount plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52007.STL 52007.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52004.jpg]]
| + | |
| − | | align="Left" | '''52004'''
| + | |
| − | | align="Left" | Optional HS1177 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52004.STL 52004.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52005.jpg]]
| + | |
| − | | align="Left" | '''52005'''
| + | |
| − | | align="Left" | Optional HS1184 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52005.STL 52005.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Hardware Shown'''<br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Quantity'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Philips head machine screw, M3 x 8mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Socket head cap screw, M3 x 10mm, Steel
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Standoff, M3 x 10mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 3x
| + | |
| − | | align="Left" | Flathead machine screw, M3 x 10mm, Steel
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | === Brushless Roll Attachment ===
| + | |
| − | | + | |
| − | This is a new addition to the line-up. The canopy has an extra large cut-out so that a brushless gimbal roll attachment can be utilized with some protection for additional electronics like controller, cam switch, etc. The version shown here uses a small 22mm OD motor, a Multistar 1807/340kv.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:47013R.jpg|700px]]
| + | |
| − | |-
| + | |
| − | | align="center" | Roll attachment shown with an early prototype canopy and the Mobius Mini
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | This really is designed for the Mobius Mini but a larger camera could be used with a slightly larger Gimbal motor such as a 2208-80t/90kv unit. Some canopy trimming may have to be done if an alternate motor is used.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1003.jpg|1000px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47013T.JPG]]
| + | |
| − | | align="Left" | '''47013'''
| + | |
| − | | align="Left" | Canopy, Roll attachment
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47013.STL 47013.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54002.jpg]]
| + | |
| − | | align="Left" | '''54002'''
| + | |
| − | | align="Left" | Front deck plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54002.STL 54002.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54001.jpg]]
| + | |
| − | | align="Left" | '''54001'''
| + | |
| − | | align="Left" | Rear deck plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54001.STL 54001.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52006.jpg]]
| + | |
| − | | align="Left" | '''52006'''
| + | |
| − | | align="Left" | Canopy support, rib
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52006.STL 52006.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52011.jpg]]
| + | |
| − | | align="Left" | '''52011'''
| + | |
| − | | align="Left" | Roll attachment camera plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52011.STL 52011.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52013.jpg]]
| + | |
| − | | align="Left" | '''52013'''
| + | |
| − | | align="Left" | Roll attachment end plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52013.STL 52013.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52012.jpg]]
| + | |
| − | | align="Left" | '''52012'''
| + | |
| − | | align="Left" | Roll attachment motor stand
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52012.STL 52012.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52004.jpg]]
| + | |
| − | | align="Left" | '''52004'''
| + | |
| − | | align="Left" | Optional HS1177 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52004.STL 52004.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52005.jpg]]
| + | |
| − | | align="Left" | '''52005'''
| + | |
| − | | align="Left" | Optional HS1184 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52005.STL 52005.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Hardware Shown'''<br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Quantity'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Philips head machine screw, M3 x 8mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Socket head cap screw, M3 x 10mm, Steel
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Standoff, M3 x 10mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 5x
| + | |
| − | | align="Left" | Flathead machine screw, M3 x 10mm, Steel
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Flathead machine screw, M2.5 x 6mm, Steel
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Socket head cap screw, M2.5 x 6mm, Steel
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | === Light Weight Pan and Tilts ===
| + | |
| − | | + | |
| − | This is also a new release. Both the "Lightweight Pan and Tilt" and the "Lightweight Pan and Tilt - v2" I have published on Thingiverse will bolt directly to the canopy.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:47009R.jpg|700px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | For more information on these two add-ons please see the Thingiverse pages here:<br><br>
| + | |
| − | | + | |
| − | : [http://www.thingiverse.com/thing:2122735 Lightweight Pan and Tilt]
| + | |
| − | : [http://www.thingiverse.com/thing:2168825 Lightweight Pan and Tilt - v2]
| + | |
| − | <br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1005.jpg|600px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47009T.jpg]]
| + | |
| − | | align="Left" | '''47009'''
| + | |
| − | | align="Left" | Canopy, Lightweight Pan and Tilt
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47009.STL 47009.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54002.jpg]]
| + | |
| − | | align="Left" | '''54002'''
| + | |
| − | | align="Left" | Front deck plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54002.STL 54002.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54001.jpg]]
| + | |
| − | | align="Left" | '''54001'''
| + | |
| − | | align="Left" | Rear deck plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54001.STL 54001.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52006.jpg]]
| + | |
| − | | align="Left" | '''52006'''
| + | |
| − | | align="Left" | Deck Plate, rib
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52006.STL 52006.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52004.jpg]]
| + | |
| − | | align="Left" | '''52004'''
| + | |
| − | | align="Left" | Optional HS1177 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52004.STL 52004.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52005.jpg]]
| + | |
| − | | align="Left" | '''52005'''
| + | |
| − | | align="Left" | Optional HS1184 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52005.STL 52005.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Hardware Shown'''<br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Quantity'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Philips head machine screw, M3 x 8mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Socket head cap screw, M3 x 10mm, Steel
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Standoff, M3 x 10mm, Nylon
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | === Heavy Duty Pan and Tilt ===
| + | |
| − | | + | |
| − | This is the same set-up as previously released but with the new canopy and FPV camera mounts which lower the cameras enough to clear the bottom edge of the canopy. For more information on the P&T parts and hardware please see the P&T article here - [[Heavy Duty Pan and Tilt]] <br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1006.jpg|600px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:47015T.jpg]]
| + | |
| − | | align="Left" | '''47007'''
| + | |
| − | | align="Left" | Canopy, Heavy Duty Pan and Tilt
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/47007.STL 47007.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54003.jpg]]
| + | |
| − | | align="Left" | '''54003'''
| + | |
| − | | align="Left" | GWS Servo mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/54003.STL 54003.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:2205.JPG]]
| + | |
| − | | align="Left" | '''2205'''
| + | |
| − | | align="Left" | GWS Servo bearing plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/2205.STL 2205.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52004.jpg]]
| + | |
| − | | align="Left" | '''52004'''
| + | |
| − | | align="Left" | Optional HS1177 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52004.STL 52004.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52005.jpg]]
| + | |
| − | | align="Left" | '''52005'''
| + | |
| − | | align="Left" | Optional HS1184 Camera Mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52005.STL 52005.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Hardware Shown'''<br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Quantity'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | |-
| + | |
| − | | align="Left" | 4x
| + | |
| − | | align="Left" | Philips head machine screw, M3 x 8mm, Nylon
| + | |
| − | |-
| + | |
| − | | align="Left" | 2x
| + | |
| − | | align="Left" | Socket head cap screw, M3 x 10mm, Steel
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | == Plain Decks ==
| + | |
| − | | + | |
| − | This section has a few "Plain" decks. These are generally not compatible with any of the canopies and are full coverage decks which cover all the foam on the front of the fuselage.<br><br>
| + | |
| − | | + | |
| − | === Simple GWS Servo Deck ===
| + | |
| − | | + | |
| − | If all you need is a simple deck to mount the GWS S125-1T, 360 degree servo, this is it. This deck puts the servo forward so a Pan and Tilt can look straight down over the nose. Additionally, if you want to add the heavy duty bearing plate and servo coupler, the bosses are here and ready to be tapped to M3 for the bearing plate stand-offs.<br><br>
| + | |
| − | | + | |
| − | '''NOTE''': This is a full coverage deck and is not compatible with any of the canopies.
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:47101.JPG|700px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54005.JPG]]
| + | |
| − | | align="Left" | '''54005'''
| + | |
| − | | align="Left" | Front deck plate, wide, GWS
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/54005.STL 54005.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:54006.JPG]]
| + | |
| − | | align="Left" | '''54006'''
| + | |
| − | | align="Left" | Rear deck plate, wide
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/54006.STL 54006.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52006.jpg]]
| + | |
| − | | align="Left" | '''52006'''
| + | |
| − | | align="Left" | Deck plate support rib
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/canopy/52006.STL 52006.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | == Skid Plates ==
| + | |
| − | === Front Skids ===
| + | |
| − | | + | |
| − | If you want the best fore and aft skid protection then look no further! These skids have been tested 100's of times on some of the worst landing surfaces you could imagine and they do the job. There are two versions of the front skid, one wide, one narrow. The wide, 2 piece, skid does a better job in cut shale or other super abrasive surfaces, the narrow version is lighter and printable as a single piece.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:MT_FRONT_SKID2.jpg|500px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:52101B.JPG|800px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:52101C.JPG|800px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52101.JPG]]
| + | |
| − | | align="Left" | '''52101'''
| + | |
| − | | align="Left" | Front skid, nose piece
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52101.STL 52101.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52102.JPG]]
| + | |
| − | | align="Left" | '''52102'''
| + | |
| − | | align="Left" | Front skid, flat piece
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52102.STL 52102.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52103.JPG]]
| + | |
| − | | align="Left" | '''52103'''
| + | |
| − | | align="Left" | Front skid, 1 piece narrow
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52103.STL 52103.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | === Rear Skid ===
| + | |
| − | | + | |
| − | This skid does an amazing job of keeping the rear lower fin intact and straight.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:MT_REAR_SKID2.jpg|500px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52104.JPG]]
| + | |
| − | | align="Left" | '''52104'''
| + | |
| − | | align="Left" | Rear skid
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52104.STL 52104.STL]
| + | |
| − | |}
| + | |
| − | {{Clear}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | : Use E6000, Beacons FoamTac or UHU-POR glue to fasten skid pieces in place.
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS is recommended for these parts. They will fit and work excellently on 0.2mm resolution and slow to moderate print speed. The rear skid can be printed right-side up or down, both with supports. It will look best printed down-side up but this is difficult to print for some.
| + | |
| − | <br><br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | == Gear Decks ==
| + | |
| − | | + | |
| − | Below are two gear decks for mounting electronics in the fuselage. The first "Main Gear Deck" bolts into the center structure and is a great place to mount a flight controller and other bits. The second "Rear Gear Deck" sits just behind the wood center structure and is a great place to mount an RX, GPS puck or ESC.<br><br>
| + | |
| − | | + | |
| − | === Main Gear Deck ===
| + | |
| − | | + | |
| − | Having a bolt-in gear deck is a really nice feature in any build. Many have re-designed the entire wood structure but I find this to be redundant, unnecessary work as the wood structure is quite good, stronger than PLA or ABS of the same dimensions and very easy to work with.<br><br>
| + | |
| − | | + | |
| − | This gear deck then uses four threaded clips which glue nicely to the wood structure and put the deck just above the bottom of the structure. You could also elect to use four rubber dampers if you are having vibration issues. The first picture below is an older version of this deck which can be found on [http://www.thingiverse.com/thing:1751857 Thingiverse] if you think it will better suit your needs.<br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:NMT41.jpg|700px]]
| + | |
| − | |-
| + | |
| − | | align="center" | Older version with outside deck clips
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:1021.JPG|700px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52017.JPG]]
| + | |
| − | | align="Left" | '''52017'''
| + | |
| − | | align="Left" | Gear deck
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52017.STL 52017.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52015.JPG]]
| + | |
| − | | align="Left" | '''52015'''
| + | |
| − | | align="Left" | Gear deck clip 'A'
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52015.STL 52015.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52016.JPG]]
| + | |
| − | | align="Left" | '''52016'''
| + | |
| − | | align="Left" | Gear deck clip 'B'
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52016.STL 52016.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:1021STL.JPG]]
| + | |
| − | | align="Left" | '''1021STL'''
| + | |
| − | | align="Left" | Complete STL group
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/1021STL.STL 1021STL.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | :1. Print the "Complete STL group" file
| + | |
| − | :2. Tap the four clips to M3
| + | |
| − | :3. Assemble the deck in the wood structure using four M3 machine screws <u>AFTER</u> the wood structure is installed in the plane
| + | |
| − | :4. Make sure all four clips are lined up evenly and fully seated against the wood
| + | |
| − | :5. Use thin CA to secure the clips to the wood being careful not to glue the deck to the clips
| + | |
| − | <br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:52015M.JPG|400px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS or PLA is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | <br><br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | === Rear Gear Deck ===
| + | |
| − | | + | |
| − | The rear deck idea came from a poster on RCGroups as a way to mount an ESC directly under an air vent in the hatch. I really liked this idea so came up with my own version which pivots up so you can get to anything below the deck if and when needed.
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:52021.JPG|700px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="0" cellspacing="1" cellpadding="1" align="center"
| + | |
| − | |-
| + | |
| − | | align="center" | [[File:52021E.JPG|700px]]
| + | |
| − | |}
| + | |
| − | <br><br>
| + | |
| − | | + | |
| − | {| border="1" cellspacing="1" cellpadding="1" align="left"
| + | |
| − | |-
| + | |
| − | | width="200" align="Left" | '''Image'''
| + | |
| − | | width="100" align="Left" | '''Part Number'''
| + | |
| − | | width="400" align="Left" | '''Part Description'''
| + | |
| − | | width="100" align="Center" | '''Print File'''
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52018.JPG]]
| + | |
| − | | align="Left" | '''52018'''
| + | |
| − | | align="Left" | Deck pivot mount
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52018.STL 52018.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52019.JPG]]
| + | |
| − | | align="Left" | '''52019'''
| + | |
| − | | align="Left" | Rear deck plate
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52019.STL 52019.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52020.JPG]]
| + | |
| − | | align="Left" | '''52020'''
| + | |
| − | | align="Left" | Rear deck mount hold-down
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52020.STL 52020.STL]
| + | |
| − | |-
| + | |
| − | | align="Left" | [[File:52021STL.JPG]]
| + | |
| − | | align="Left" | '''52021STL'''
| + | |
| − | | align="Left" | Complete rear deck STL group
| + | |
| − | | align="Center" | [http://www.itsqv.com/QVM/files/parts/52021STL.STL 52021STL.STL]
| + | |
| − | |}
| + | |
| − | {{Clear1}}
| + | |
| − | | + | |
| − | '''Install'''
| + | |
| − | | + | |
| − | :1. Print the "Complete STL group" file or the individual parts
| + | |
| − | :2. Tap the the two pivot ears to M3
| + | |
| − | :3. Tap the two rear mounts to M3
| + | |
| − | :4. Mount the deck to the pivot piece with two M3 x 8mm screws (I use nylon screws)
| + | |
| − | :5. Snap the pivot piece into the center of the rear wood cross-piece
| + | |
| − | :6. Wick in some thin CA glue
| + | |
| − | :7. Pivot the deck to level and mark the side foam where the rear mounts are to go
| + | |
| − | :8. Use E6000 or UHU-POR glue to glue the mounts in place and screw the deck down to hold it all together while the glue sets
| + | |
| − | <br>
| + | |
| − | | + | |
| − | '''Print Recomendations'''
| + | |
| − | | + | |
| − | : ABS or PLA is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.
| + | |
| − | | + | |
| − | <br><br>
| + | |
| − | ----
| + | |
| − | | + | |
| − | == Wing Mount Motors ==
| + | |
| − | | + | |
| − | TBA
| + | |
| − | | + | |
| − | == Misc Mini Talon Parts ==
| + | |
| − | | + | |
| − | TBA
| + | |
| − | | + | |
| − | == See Also ==
| + | |
| − | | + | |
| − | TBA
| + | |
| − | | + | |
| − | === Comments? Questions? ===
| + | |
| − | | + | |
| − | :* '''<u>[mailto:qmar80@hotmail.com?Subject=About%20The%20Mini%20Talon%20Parts%20&body=Question? email me!]</u>'''
| + | |
| − | | + | |
| − | <br><br><br>
| + | |
| − | [[Category:Contents]]
| + | |
