Difference between revisions of "Mini Talon Parts Compilation"

From ItsQv
Jump to: navigation, search
(→‎Skid Plates)
Line 467: Line 467:
 
== Skid Plates ==
 
== Skid Plates ==
  
−
TBA
+
If you want the best fore and aft skid protection then look no further! These skids have been tested 100's of times on some of the worst landing surfaces you could imagine and they do the job. There are two versions of the front skid, one wide, one narrow. The wide, 2 piece, skid does a better job in cut shale or other super abrasive surfaces, the narrow version is lighter and printable as a single piece.<br><br>
 +
 
 +
{| border="0" cellspacing="1" cellpadding="1" align="center"
 +
|-
 +
| align="center" | [[File:MT_FRONT_SKID2.jpg|400px]][[File:MT_REAR_SKID2.jpg|400px]]
 +
|}
 +
<br><br>
 +
 
 +
{| border="0" cellspacing="1" cellpadding="1" align="center"
 +
|-
 +
| align="center" | [[File:52101B.JPG|800px]]
 +
|}
 +
<br><br>
 +
 
 +
{| border="0" cellspacing="1" cellpadding="1" align="center"
 +
|-
 +
| align="center" | [[File:52101C.JPG|800px]]
 +
|}
 +
<br><br>
 +
 
 +
{| border="1" cellspacing="1" cellpadding="1" align="left"
 +
|-
 +
| width="200" align="Left" | '''Image'''
 +
| width="100" align="Left" | '''Part Number'''
 +
| width="400" align="Left" | '''Part Description'''
 +
| width="100" align="Center" | '''Print File'''
 +
|-
 +
| align="Left" | [[File:52101.JPG]]
 +
| align="Left" | '''52101'''
 +
| align="Left" | Front skid, nose piece
 +
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52101.STL 52101.STL]
 +
|-
 +
| align="Left" | [[File:52102.JPG]]
 +
| align="Left" | '''52102'''
 +
| align="Left" | Front skid, flat piece
 +
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52102.STL 52102.STL]
 +
|-
 +
| align="Left" | [[File:52103.JPG]]
 +
| align="Left" | '''52103'''
 +
| align="Left" | Front skid, 1 piece narrow
 +
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52103.STL 52103.STL]
 +
|}
 +
{{Clear1}}
 +
 
 +
'''Rear Skid'''<br><br>
 +
 
 +
{| border="1" cellspacing="1" cellpadding="1" align="left"
 +
|-
 +
| width="200" align="Left" | '''Image'''
 +
| width="100" align="Left" | '''Part Number'''
 +
| width="400" align="Left" | '''Part Description'''
 +
| width="100" align="Center" | '''Print File'''
 +
|-
 +
| align="Left" | [[File:52104.JPG]]
 +
| align="Left" | '''52104'''
 +
| align="Left" | Rear skid
 +
| align="Center" | [http://www.itsqv.com/QVM/files/parts/52104.STL 52104.STL]
 +
|}
 +
{{Clear}}
 +
 
 +
'''Install'''
 +
 
 +
: Use E6000, Beacons FoamTac or UHU-POR glue to fasten skid pieces in place.
 +
<br>
 +
 
 +
'''Print Recomendations'''
 +
 
 +
: ABS is recommended for these parts. They will fit and work excellently on 0.2mm resolution and slow to moderate print speed. The rear skid can be printed right-side up or down, both with supports. It will look best printed down-side up but this is difficult to print for some.
 +
<br><br>
 +
----
  
 
== Gear Deck ==
 
== Gear Deck ==

Revision as of 20:29, 29 March 2017

Tools.jpg This page or section is under construction and will change going forward.

Questions or Comments? Please contact the Wiki administrator

March, 2017

Parts .jpg
  Ready for printing!


Introduction

This article is a collection of 3D print parts specifically designed to fit the X-UAV Mini Talon. These have all been printed and most have been flight tested and even a few - crash tested :).

Enjoy - Mark

Canopy's and Set-ups

I have redone the feature set that makes up this 3D model smoothing out the surface and profile and changing the NACA style vent to side air scoop type vents. It prints more cleanly now and I have added a version which will support either the Geared Pan & Tilt or the 390deg Pan & Tilt. Below you will find the latest versions of this fun design with downloads for all the printable STL files.

Plain Canopy

If you want to simply cover the nose for a more appealing look or need something to fit to your own structure this may be the part you want. The two FPV camera mounts are optional.

1001.jpg



Image Part Number Part Description Print File
47001T.jpg 47001 Canopy, Plain 47001.STL
52001.jpg 52001 Canopy support, front 52001.STL
52002.jpg 52002 Canopy support, rear 52002.STL
52004.jpg 52004 Optional HS1177 Camera Mount 52004.STL
52005.jpg 52005 Optional HS1184 Camera Mount 52005.STL


Hardware Shown

Quantity Part Description
4x Philips head machine screw, M3 x 8mm, Nylon
2x Socket head cap screw, M3 x 10mm, Steel


Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front support and rear catch in place.


Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.



Static Camera Mounts

This version has a cut-out and platform for the Mobius style HD cams and is the most aerodynamic of all the camera mount units. There are two different canopies, one specifically for the Mobius Mini and one which will accomodate either the Mobius or Runcam cameras.

1002.jpg



Image Part Number Part Description Print File
47003T.jpg 47003 Canopy, Mobius Mini 47003.STL
47005T.jpg 47005 Canopy, Mobius/Runcam 47005.STL
54002.jpg 54002 Front deck plate 54002.STL
54001.jpg 54001 Rear deck plate 54001.STL
52006.jpg 52006 Canopy support, rib 52006.STL
52007.jpg 52007 Camera mount plate 52007.STL
52004.jpg 52004 Optional HS1177 Camera Mount 52004.STL
52005.jpg 52005 Optional HS1184 Camera Mount 52005.STL


Hardware Shown

Quantity Part Description
4x Philips head machine screw, M3 x 8mm, Nylon
2x Socket head cap screw, M3 x 10mm, Steel
2x Standoff, M3 x 10mm, Nylon
3x Flathead machine screw, M3 x 10mm, Steel


Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.


Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.


Brushless Roll Attachment

This is a new addition to the line-up. The canopy has an extra large cut-out so that a brushless gimbal roll attachment can be utilized with some protection for additional electronics like controller, cam switch, etc. The version shown here uses a small 22mm OD motor, a Multistar 1807/340kv.

47013R.jpg
Roll attachment shown with an early prototype canopy and the Mobius Mini



This really is designed for the Mobius Mini but a larger camera could be used with a slightly larger Gimbal motor such as a 2208-80t/90kv unit. Some canopy trimming may have to be done if an alternate motor is used.

1003.jpg



Image Part Number Part Description Print File
47013T.JPG 47013 Canopy, Roll attachment 47013.STL
54002.jpg 54002 Front deck plate 54002.STL
54001.jpg 54001 Rear deck plate 54001.STL
52006.jpg 52006 Canopy support, rib 52006.STL
52011.jpg 52011 Roll attachment camera plate 52011.STL
52013.jpg 52013 Roll attachment end plate 52013.STL
52012.jpg 52012 Roll attachment motor stand 52012.STL
52004.jpg 52004 Optional HS1177 Camera Mount 52004.STL
52005.jpg 52005 Optional HS1184 Camera Mount 52005.STL


Hardware Shown

Quantity Part Description
4x Philips head machine screw, M3 x 8mm, Nylon
2x Socket head cap screw, M3 x 10mm, Steel
2x Standoff, M3 x 10mm, Nylon
5x Flathead machine screw, M3 x 10mm, Steel
4x Flathead machine screw, M2.5 x 6mm, Steel
4x Socket head cap screw, M2.5 x 6mm, Steel


Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.


Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.


Light Weight Pan and Tilts

This is also a new release. Both the "Lightweight Pan and Tilt" and the "Lightweight Pan and Tilt - v2" I have published on Thingiverse will bolt directly to the canopy.

47009R.jpg



For more information on these two add-ons please see the Thingiverse pages here:

Lightweight Pan and Tilt
Lightweight Pan and Tilt - v2


1005.jpg



Image Part Number Part Description Print File
47009T.jpg 47009 Canopy, Heavy Duty Pan and Tilt 47009.STL
54002.jpg 54002 Front deck plate 54002.STL
54001.jpg 54001 Rear deck plate 54001.STL
52006.jpg 52006 Deck Plate, rib 52006.STL
52004.jpg 52004 Optional HS1177 Camera Mount 52004.STL
52005.jpg 52005 Optional HS1184 Camera Mount 52005.STL


Hardware Shown

Quantity Part Description
4x Philips head machine screw, M3 x 8mm, Nylon
2x Socket head cap screw, M3 x 10mm, Steel
2x Standoff, M3 x 10mm, Nylon



Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.


Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.


Heavy Duty Pan and Tilt

This is the same set-up as previously released but with the new canopy and FPV camera mounts which lower the cameras enough to clear the bottom edge of the canopy. For more information on the P&T parts and hardware please see the P&T article here - Heavy Duty Pan and Tilt

1006.jpg



Image Part Number Part Description Print File
47015T.jpg 47007 Canopy, Heavy Duty Pan and Tilt 47007.STL
54003.jpg 54003 GWS Servo mount 54003.STL
2205.JPG 2205 GWS Servo mount 2205.STL
52004.jpg 52004 Optional HS1177 Camera Mount 52004.STL
52005.jpg 52005 Optional HS1184 Camera Mount 52005.STL


Hardware Shown

Quantity Part Description
4x Philips head machine screw, M3 x 8mm, Nylon
2x Socket head cap screw, M3 x 10mm, Steel


Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.


Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.


Plain Decks

TBA

47101.jpg



Skid Plates

If you want the best fore and aft skid protection then look no further! These skids have been tested 100's of times on some of the worst landing surfaces you could imagine and they do the job. There are two versions of the front skid, one wide, one narrow. The wide, 2 piece, skid does a better job in cut shale or other super abrasive surfaces, the narrow version is lighter and printable as a single piece.

MT FRONT SKID2.jpgMT REAR SKID2.jpg



52101B.JPG



52101C.JPG



Image Part Number Part Description Print File
52101.JPG 52101 Front skid, nose piece 52101.STL
52102.JPG 52102 Front skid, flat piece 52102.STL
52103.JPG 52103 Front skid, 1 piece narrow 52103.STL


Rear Skid

Image Part Number Part Description Print File
52104.JPG 52104 Rear skid 52104.STL



Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten skid pieces in place.


Print Recomendations

ABS is recommended for these parts. They will fit and work excellently on 0.2mm resolution and slow to moderate print speed. The rear skid can be printed right-side up or down, both with supports. It will look best printed down-side up but this is difficult to print for some.



Gear Deck

TBA

Wing Mount Motors

TBA

Misc Mini Talon Parts

TBA

See Also

TBA

Comments? Questions?




Retrieved from "http://www.itsqv.com/QVM/index.php?title=Mini_Talon_Parts_Compilation&oldid=2824"