Difference between revisions of "Mini Talon Parts Compilation"

Revision as of 19:24, 29 March 2017

This page or section is under construction and will change going forward. Questions or Comments? Please contact the Wiki administrator

March, 2017

Contents 1 Introduction 2 Canopy's and Set-ups 2.1 Plain Canopy 2.2 Static Camera Mounts 2.3 Brushless Roll Attachment 2.4 Light Weight Pan and Tilts 2.5 Heavy Duty Pan and Tilt 3 Plain Decks 4 Skid Plates 5 Gear Deck 6 Wing Mount Motors 7 Misc Mini Talon Parts 8 See Also 8.1 Comments? Questions?
	Ready for printing!

Introduction

This article is a collection of 3D print parts specifically designed to fit the X-UAV Mini Talon. These have all been printed and most have been flight tested and even a few - crash tested :).

Enjoy - Mark

Canopy's and Set-ups

I have redone the feature set that makes up this 3D model smoothing out the surface and profile and changing the NACA style vent to side air scoop type vents. It prints more cleanly now and I have added a version which will support either the Geared Pan & Tilt or the 390deg Pan & Tilt. Below you will find the latest versions of this fun design with downloads for all the printable STL files.

Plain Canopy

If you want to simply cover the nose for a more appealing look or need something to fit to your own structure this may be the part you want. The two FPV camera mounts are optional.

Image	Part Number	Part Description	Print File
	47001	Canopy, Plain	47001.STL
	52001	Canopy support, front	52001.STL
	52002	Canopy support, rear	52002.STL
	52004	Optional HS1177 Camera Mount	52004.STL
	52005	Optional HS1184 Camera Mount	52005.STL

Hardware Shown

Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front support and rear catch in place.

Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.

Static Camera Mounts

This version has a cut-out and platform for the Mobius style HD cams and is the most aerodynamic of all the camera mount units. There are two different canopies, one specifically for the Mobius Mini and one which will accomodate either the Mobius or Runcam cameras.

Image	Part Number	Part Description	Print File
	47003	Canopy, Mobius Mini	47003.STL
	47005	Canopy, Mobius/Runcam	47005.STL
	54002	Front deck plate	54002.STL
	54001	Rear deck plate	54001.STL
	52006	Canopy support, rib	52006.STL
	52007	Camera mount plate	52007.STL
	52004	Optional HS1177 Camera Mount	52004.STL
	52005	Optional HS1184 Camera Mount	52005.STL

Hardware Shown

Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.

Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.

Brushless Roll Attachment

This is a new addition to the line-up. The canopy has an extra large cut-out so that a brushless gimbal roll attachment can be utilized with some protection for additional electronics like controller, cam switch, etc. The version shown here uses a small 22mm OD motor, a Multistar 1807/340kv.

Roll attachment shown with an early prototype canopy and the Mobius Mini

This really is designed for the Mobius Mini but a larger camera could be used with a slightly larger Gimbal motor such as a 2208-80t/90kv unit. Some canopy trimming may have to be done if an alternate motor is used.

Image	Part Number	Part Description	Print File
	47013	Canopy, Roll attachment	47013.STL
	54002	Front deck plate	54002.STL
	54001	Rear deck plate	54001.STL
	52006	Canopy support, rib	52006.STL
	52011	Roll attachment camera plate	52011.STL
	52013	Roll attachment end plate	52013.STL
	52012	Roll attachment motor stand	52012.STL
	52004	Optional HS1177 Camera Mount	52004.STL
	52005	Optional HS1184 Camera Mount	52005.STL

Hardware Shown

Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.

Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.

Light Weight Pan and Tilts

This is also a new release. Both the "Lightweight Pan and Tilt" and the "Lightweight Pan and Tilt - v2" I have published on Thingiverse will bolt directly to the canopy.

For more information on these two add-ons please see the Thingiverse pages here:

Lightweight Pan and Tilt

Lightweight Pan and Tilt - v2

Image	Part Number	Part Description	Print File
	47009	Canopy, Heavy Duty Pan and Tilt	47009.STL
	54002	Front deck plate	54002.STL
	54001	Rear deck plate	54001.STL
	52006	Deck Plate, rib	52006.STL
	52004	Optional HS1177 Camera Mount	52004.STL
	52005	Optional HS1184 Camera Mount	52005.STL

Hardware Shown

Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.

Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.

Heavy Duty Pan and Tilt

This is the same set-up as previously released but with the new canopy and FPV camera mounts which lower the cameras enough to clear the bottom edge of the canopy. For more information on the P&T parts and hardware please see the P&T article here - Heavy Duty Pan and Tilt

Image	Part Number	Part Description	Print File
	47007	Canopy, Heavy Duty Pan and Tilt	47007.STL
	54003	GWS Servo mount	54003.STL
	2205	GWS Servo mount	2205.STL
	52004	Optional HS1177 Camera Mount	52004.STL
	52005	Optional HS1184 Camera Mount	52005.STL

Hardware Shown

Install

Use E6000, Beacons FoamTac or UHU-POR glue to fasten front and rear decks and ribs in place.

Print Recomendations

ABS is recommended for this part. It will fit and work fine on 0.2mm resolution and slow to moderate print speed.

Plain Decks

TBA

Skid Plates

TBA

Gear Deck

TBA

Wing Mount Motors

TBA

Misc Mini Talon Parts

TBA

See Also

TBA

Comments? Questions?

• email me!