View source for RunCam Split Dedicated Pan and Tilt

[[File:BTI.png|link=GIMBALS|Gimbals]]<br>
<i>July 2017</i><br>
<br>
{| cellspacing="1" cellpadding="1" width="95%" border="0"
|-
| align="left" valign="top" width="50%" | __TOC__ 
| align="right" width="50%" | [[File:06RCS.jpg|650px]]
|-
| align="left" | 
| align="right" | The simple 180 degree Pan and Tilt
|}


== Introduction ==

This project started with the first RunCam Split (v1) which I bought to replace my Mobius with something more current and a little smaller. The first parts I did made up the v1 Pan and Tilt (shown above) which would bolt directly to my previous Pan and Tilts. After flying this for a bit, I decided I needed a case version I could easily move from plane to plane so I came up with several versions of the case.<br><br>

I am only showing one version of the Pan and Tilt and one version of the simple case. For more parts including compatability information please see these two parts catalogs:<br>

:* [[Parts Catalog - Pan and Tilt Parts]]
:* [[Parts Catalog - General Parts]]

== Pan and Tilt ==

The Pan and tilt has an "open" frame to allow cooling air to circulate around and through the PCB. There are two sizes of servo plates available, one to accomodate my canopy mounts and a larger one to accomodate a common plywood or flat deck. <br><br>

=== Parts & Hardware ===

{| border="0"
| [[File:RCSplit_PnT_EXPL.JPG|300px]]
| align="center" | &nbsp;
{| border="1" style="background:#ffffcc" <!-- The nested table must be on a new line -->
 | width="65" align="Center" | '''Part Number'''
 | width="220" align="Left" | &nbsp;'''Part Description'''
 | width="100" align="Center" | '''Print File'''
 | align="Left" | &nbsp;'''Compatibility'''
 |-
 | align="Left" | &nbsp;'''52100'''
 | align="Left" | &nbsp;Servo plate, flat, raised
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52100.STL 52100.STL]
 | align="Left" | &nbsp;Fits Turnigy RS5180MG servo or similar. Servo only, no gearing.
 |-
 | align="Left" | &nbsp;'''52092'''
 | align="Left" | &nbsp;Lower bracket, small
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52092.STL 52092.STL]
 | align="Left" | &nbsp;Supports all Camera Plates. See part sketch for mount hole spacing.
 |-
 | align="Left" | &nbsp;'''52062'''
 | align="Left" | &nbsp;Camera plate, RunCam Split
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52062.STL 52062.STL]
 | align="Left" | &nbsp;Fits all Yaw Brackets. Designed for the RunCam Split & Split v2 cameras. Use with 52067 and 52076 for  v1 or 52135 for v2
 |-
 | align="Left" | &nbsp;'''52067'''
 | align="Left" | &nbsp;RunCam Split v1 PCB Cover, Top
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52067.STL 52067.STL]
 | align="Left" | &nbsp;Pair with 52062 camera plate for RunCam Split v1
 |-
 | align="Left" | &nbsp;'''52076'''
 | align="Left" | &nbsp;RunCam Split v1 SD Card Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52076.STL 52076.STL]
 | align="Left" | &nbsp;Pair with 52062 camera plate for RunCam Split v1. Snaps into 52067 top cover
 |-
 | align="Left" | &nbsp;'''52135'''
 | align="Left" | &nbsp;RunCam Split v2 PCB Cover, Top
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52135.STL 52135.STL]
 | align="Left" | &nbsp;Pair with 52062 camera plate for RunCam Split v2
|}<br><br>
{| border="0" align="Left"
| align="Left" | '''Hardware'''<br>
: 4x M3 x 10mm Philips Head Screw, Nylon
: 4x M3 x 5mm Stand-off, Nylon
: 2x M3 x 12mm Philips Head Screw, Nylon
: 2x M3 Hex Nut, Nylon
: 4x M2 Hex nut
: 4x M2 x 10mm Socket Head Machine Screw
: 4x M2 Flatwasher
: 4x M2 Hex Nut
: 4x M2 x 6mm Flathead Screw
: 0.047" x 50mm Steel wire
|}
|}
<br><br>

'''Servo Selection:'''<br>
Pan Servo - For this non-geared Pan and Tilt I selected the Turnigy™ TGY-180D 180 degree Digital Servo from HobbyKing. It is important to use a digital if you are also using a VTX of 600mw or more to avoid the noise these components can produce in the servo.<br><br>

Tilt Servo - Many of the current 9-12 gram servos will fit the tilt plate. A Corona DS929MG is what I use.
<br><br>


== RunCam Split Case ==

The case I am showing here is very simple. It is three parts for the v1 Split and two parts for the v2. It has an open frame so that air will circulate around the PCB. It uses the stock short camera module cable.<br><br>

{| border="0" cellspacing="1" cellpadding="1" align="center"
|-
| align="center" | [[File:RCSplitCases2.jpg|900px]]
|}
<br><br>

=== Parts and Hardware ===

{| border="0"
| [[File:RCS_Case.jpg|300px]]
| align="center" | &nbsp;
{| border="1" style="background:#ffffcc" <!-- The nested table must be on a new line -->
 | width="50" align="Center" | '''Item'''
 | width="65" align="Center" | '''Part Number'''
 | width="220" align="Left" | &nbsp;'''Part Description'''
 | width="100" align="Center" | '''Print File'''
 | width="200" align="Left" | &nbsp;'''Compatibility'''
 |-
 | align="Center" | &nbsp;'''1'''
 | align="Left" | &nbsp;&nbsp;'''52076'''
 | align="Left" | &nbsp;SD Card Snap Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52076.STL 52076.STL]
 | align="Left" | &nbsp;Fits 52067 Cover.
 |-
 | align="Center" | &nbsp;'''2'''
 | align="Left" | &nbsp;&nbsp;'''52067'''
 | align="Left" | &nbsp;RCS v1 PCB Top Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52067.STL 52067.STL]
 | align="Left" | &nbsp;Fits RunCam Split V1
 |-
 | align="Center" | &nbsp;'''3'''
 | align="Left" | &nbsp;&nbsp;'''52087'''
 | align="Left" | &nbsp;RCS PCB Bottom Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52087.STL 52087.STL]
 | align="Left" | &nbsp;Fits RunCam Split V1
 |-
 | align="Center" | &nbsp;'''4'''
 | align="Left" | &nbsp;&nbsp;'''52135'''
 | align="Left" | &nbsp;RCS v2 PCB Top Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52135.STL 52135.STL]
 | align="Left" | &nbsp;Fits RunCam Split V2
 |-
 | align="Center" | &nbsp;'''5'''
 | align="Left" | &nbsp;&nbsp;'''52134'''
 | align="Left" | &nbsp;RCS v2 PCB Bottom Cover
 | align="Center" | &nbsp;[http://www.itsqv.com/QVM/files/parts/52134.STL 52134.STL]
 | align="Left" | &nbsp;Fits RunCam Split V2
|}<br><br>
{| border="0" align="Left"
| align="Left" | '''Hardware'''<br>
: 4x M3 x 10mm Philips Head Screw, Nylon
: 4x M2 x 5mm Button Head Screw (RunCam)
|}
|}
<br><br>

== See Also  ==
<br>
:* [[ 390 Degree Geared Pan and Tilt]]
:* [[Forward Offset Pan %26 Tilt]]
:* [[Heavy Duty Pan and Tilt]]
:* [[Gimbals,_Mounts_and_Controllers | Gimbals!]]
<br>

=== Comments? Questions? ===

:* '''<u>[mailto:qmar80@hotmail.com?Subject=About%20The%20RunCam%20Split%20Pan%20and%20Tilt&body=Question? email me!]</u>'''

<br><br>

[[Category:Contents]]